Direct injection

TYPE TF/FN-1
TF/TF6-1 ~ FN/FNH6-1T ~ FN/FNH6-1MDT ~ FT/FTH6-1MD

TYPE FN/FNH6-1T: Nozzle suitable for moulding parts where good injection point vestige is required. It is suggested only if the injected material is EPDM, HDPE, LDPE, LLDPE, PP, PS. is not suitable for moulding materials with abrasive charges.
TYPE FN/FNH6-1MDT: Nozzle suitable for moulding parts where good injection point appearance is required. Unlike the FN-1T nozzle, it is suitable for moulding materials as EPDM, HDPE, LDPE, LLDPE, PP, PS with abrasive fillers.
TYPE FT/FTH6-1MD ~ TF/TF6-1: Nozzle suitable for moulding parts where good injection point appearance is required. Unlike the FN-1MDT nozzle, is recommended for all other polymers also with abrasive fillers.

Catalogue

Multicavity nozzle
Single nozzle

YOU MUST FILL IN THE FIELD NOZZLE DIAMETER

Nozzle diameter:

Diameter of the nozzle seat

2D/3D drawings download - Nozzle

YOU MUST FILL IN THE FIELD HEATER

YOU MUST FILL IN THE FIELD LENGTH

Heater wire exit:

Heater wire exit can be on the top or in the middle of the nozzle. Heater wire exit in the middle allows the replacement of heater whilst the mould is assembled on the injection device.

Nozzle length:

Distance in the mould between the lower surface of the nozzle head and the injection gate. The gate is at the end of the nozzle and the beginning of the moulded piece.

YOU MUST FILL IN THE FIELD TIP TYPE

Select tip type:

2D/3D drawings download - Bushing

YOU MUST FILL IN THE FIELD TYPE BUSHING

Type Bushing:

Nozzle bushing can be normal or conditioned.

YOU MUST FILL IN THE FIELD BUSHING LENGTH

Bushing Length:

Conditioned bushing are without spacers and they are provided in 2 standard lenghts.

YOU MUST FILL IN THE FIELD SPACER HEIGHT

Spacer Height:

Spacers can be used when it is required to have a bushing longer than the standard ones. Spacers cannot be used with conditioned bushings.

TYPE TF-1B15
TF/TF6-1B15

TYPE TF/TF6-1B15: Nozzle suitable for molding parts where good injection point appearance is required. Fitted with extended tip of 1,5 mm to be housed in areas where the space is limited. Suitable for molding thin parts that require fast cycles. The nozzle is suitable for molding materials with abrasive fillers with maximum 20%. The nozzle is not suitable for quick colour changes.

Catalogue

Multicavity nozzle
Single nozzle

YOU MUST FILL IN THE FIELD NOZZLE DIAMETER

Nozzle diameter:

Diameter of the nozzle seat

2D/3D drawings download - Nozzle

YOU MUST FILL IN THE FIELD HEATER

YOU MUST FILL IN THE FIELD LENGTH

Heater wire exit:

Heater wire exit can be on the top or in the middle of the nozzle. Heater wire exit in the middle allows the replacement of heater whilst the mould is assembled on the injection device.

Nozzle length:

Distance in the mould between the lower surface of the nozzle head and the injection gate. The gate is at the end of the nozzle and the beginning of the moulded piece.

YOU MUST FILL IN THE FIELD TIP TYPE

Select tip type:

2D/3D drawings download - Bushing

YOU MUST FILL IN THE FIELD TYPE BUSHING

Type Bushing:

Nozzle bushing can be normal or conditioned.

YOU MUST FILL IN THE FIELD BUSHING LENGTH

Bushing Length:

Conditioned bushing are without spacers and they are provided in 2 standard lenghts.

YOU MUST FILL IN THE FIELD SPACER HEIGHT

Spacer Height:

Spacers can be used when it is required to have a bushing longer than the standard ones. Spacers cannot be used with conditioned bushings.

TYPE TF-1B50
TF/TF6-1B50

TYPE TF/TF6-1B50: Nozzle suitable for molding parts where good injection point appearance is required. Fitted with extended tip of 5 mm to be housed in areas where the space is limited. Suitable for molding thin parts that require fast cycles.
Moreover, the heating area is distant from the surface of the piece to limit halos and imperfections on the molded piece. The nozzle is not suitable for molding materials with abrasive fillers and to perform quick colour changes.
This nozzle is suitable mainly to inject polyolefin and polymers with high fluidity.

Catalogue

Multicavity nozzle
Single nozzle

YOU MUST FILL IN THE FIELD NOZZLE DIAMETER

Nozzle diameter:

Diameter of the nozzle seat

2D/3D drawings download - Nozzle

YOU MUST FILL IN THE FIELD HEATER

YOU MUST FILL IN THE FIELD LENGTH

Heater wire exit:

Heater wire exit can be on the top or in the middle of the nozzle. Heater wire exit in the middle allows the replacement of heater whilst the mould is assembled on the injection device.

Nozzle length:

Distance in the mould between the lower surface of the nozzle head and the injection gate. The gate is at the end of the nozzle and the beginning of the moulded piece.

TYPE TF-1GLT
TF/TF6-1GLT

TYPE TF/TF6-1GLT: Nozzle suitable for molding parts where appearance is of great importance. This particular tip shape allows for a uniform material distribution, therefore reducing flow paths. The application market of this nozzle is mostly cosmetics and packaging, where the appearance of the molded piece is very important.

Catalogue

Multicavity nozzle
Single nozzle

YOU MUST FILL IN THE FIELD NOZZLE DIAMETER

Nozzle diameter:

Diameter of the nozzle seat

2D/3D drawings download - Nozzle

YOU MUST FILL IN THE FIELD HEATER

YOU MUST FILL IN THE FIELD LENGTH

Heater wire exit:

Heater wire exit can be on the top or in the middle of the nozzle. Heater wire exit in the middle allows the replacement of heater whilst the mould is assembled on the injection device.

Nozzle length:

Distance in the mould between the lower surface of the nozzle head and the injection gate. The gate is at the end of the nozzle and the beginning of the moulded piece.

Select tip type:

2D/3D drawings download - Bushing

YOU MUST FILL IN THE FIELD TYPE BUSHING

Type Bushing:

Nozzle bushing can be normal or conditioned.

YOU MUST FILL IN THE FIELD BUSHING LENGTH

Bushing Length:

Conditioned bushing are without spacers and they are provided in 2 standard lenghts.

YOU MUST FILL IN THE FIELD SPACER HEIGHT

Spacer Height:

Spacers can be used when it is required to have a bushing longer than the standard ones. Spacers cannot be used with conditioned bushings.

TYPE TF/FN-1D
TF/TF6-1D ~ FN/FNH6-1D

TYPE TF/TF6-1D ~ FN/FNH6-1D: Nozzle suitable for moulding parts where good injection point appearance is required.
The nozzle is suitable for moulding materials with abrasive fillers.
Unlike to the TF-1T nozzle, the die can be machined to seal the nozzle from the mould cavity side.
The circular witness mark of the tip will remain on the moulded part.

Catalogue

Multicavity nozzle
Single nozzle

YOU MUST FILL IN THE FIELD NOZZLE DIAMETER

Nozzle diameter:

Diameter of the nozzle seat

2D/3D drawings download - Nozzle

YOU MUST FILL IN THE FIELD HEATER

YOU MUST FILL IN THE FIELD LENGTH

Heater wire exit:

Heater wire exit can be on the top or in the middle of the nozzle. Heater wire exit in the middle allows the replacement of heater whilst the mould is assembled on the injection device.

Nozzle length:

Distance in the mould between the lower surface of the nozzle head and the injection gate. The gate is at the end of the nozzle and the beginning of the moulded piece.

2D/3D drawings download - Bushing

YOU MUST FILL IN THE FIELD TYPE BUSHING

Type Bushing:

Nozzle bushing can be normal or conditioned.

YOU MUST FILL IN THE FIELD BUSHING LENGTH

Bushing Length:

Conditioned bushing are without spacers and they are provided in 2 standard lenghts.

TYPE TD/DN-1
TD/TD6-1 ~ DN/DN6-1

TYPE TD-1: Nozzle suitable for molding parts where good injection point appearance is required. Recommended for all polymers also with abrasive fillers.

Catalogue

Multicavity nozzle
Single nozzle

YOU MUST FILL IN THE FIELD NOZZLE DIAMETER

Nozzle diameter:

Diameter of the nozzle seat

2D/3D drawings download - Nozzle

YOU MUST FILL IN THE FIELD HEATER

YOU MUST FILL IN THE FIELD LENGTH

Heater wire exit:

Heater wire exit can be on the top or in the middle of the nozzle. Heater wire exit in the middle allows the replacement of heater whilst the mould is assembled on the injection device.

Nozzle length:

Distance in the mould between the lower surface of the nozzle head and the injection gate. The gate is at the end of the nozzle and the beginning of the moulded piece.

2D/3D drawings download - Bushing

YOU MUST FILL IN THE FIELD TYPE BUSHING

Type Bushing:

Nozzle bushing can be normal or conditioned.

YOU MUST FILL IN THE FIELD BUSHING LENGTH

Bushing Length:

Conditioned bushing are without spacers and they are provided in 2 standard lenghts.

YOU MUST FILL IN THE FIELD SPACER HEIGHT

Spacer Height:

Spacers can be used when it is required to have a bushing longer than the standard ones. Spacers cannot be used with conditioned bushings.

TYPE TD-1B35
TD/TD6-1B35

TYPE TD/TD6-1B35: Nozzle suitable for moulding parts where good injection point appearance is required. Fitted with extended tip of 3,5 mm to be housed in areas where the space is limited. Suitable for moulding thin parts that require fast cycles. Moreover, the heating area is distant from the surface of the piece to limit haloing and imperfections on the moulded piece. The nozzle is suitable for moulding materials with abrasive fillers but not to perform quick colour changes. For materials with very high fluidity only. If compared with TF series nozzles, TD nozzles have the sealing area on the external body rather than the tip and requires less accurate machining of the seat.

Catalogue

Multicavity nozzle
Single nozzle

YOU MUST FILL IN THE FIELD NOZZLE DIAMETER

Nozzle diameter:

Diameter of the nozzle seat

2D/3D drawings download - Nozzle

YOU MUST FILL IN THE FIELD HEATER

YOU MUST FILL IN THE FIELD LENGTH

Heater wire exit:

Heater wire exit can be on the top or in the middle of the nozzle. Heater wire exit in the middle allows the replacement of heater whilst the mould is assembled on the injection device.

Nozzle length:

Distance in the mould between the lower surface of the nozzle head and the injection gate. The gate is at the end of the nozzle and the beginning of the moulded piece.

2D/3D drawings download - Bushing

YOU MUST FILL IN THE FIELD TYPE BUSHING

Type Bushing:

Nozzle bushing can be normal or conditioned.

YOU MUST FILL IN THE FIELD BUSHING LENGTH

Bushing Length:

Conditioned bushing are without spacers and they are provided in 2 standard lenghts.

YOU MUST FILL IN THE FIELD SPACER HEIGHT

Spacer Height:

Spacers can be used when it is required to have a bushing longer than the standard ones. Spacers cannot be used with conditioned bushings.

TYPE TD-1GLT
TD/TD6-1GLT

TD-1GLT: Nozzle suitable for molding parts where appearance is of great importance. This particular tip shape allows for a uniform material distribution, therefore reducing flow paths. The application market of this nozzle is mostly cosmetics and packaging, where the appearance of the molded piece is very important.

Catalogue

Multicavity nozzle
Single nozzle

YOU MUST FILL IN THE FIELD NOZZLE DIAMETER

Nozzle diameter:

Diameter of the nozzle seat

2D/3D drawings download - Nozzle

YOU MUST FILL IN THE FIELD HEATER

YOU MUST FILL IN THE FIELD LENGTH

Heater wire exit:

Heater wire exit can be on the top or in the middle of the nozzle. Heater wire exit in the middle allows the replacement of heater whilst the mould is assembled on the injection device.

Nozzle length:

Distance in the mould between the lower surface of the nozzle head and the injection gate. The gate is at the end of the nozzle and the beginning of the moulded piece.

2D/3D drawings download - Bushing

YOU MUST FILL IN THE FIELD TYPE BUSHING

Type Bushing:

Nozzle bushing can be normal or conditioned.

YOU MUST FILL IN THE FIELD BUSHING LENGTH

Bushing Length:

Conditioned bushing are without spacers and they are provided in 2 standard lenghts.

YOU MUST FILL IN THE FIELD SPACER HEIGHT

Spacer Height:

Spacers can be used when it is required to have a bushing longer than the standard ones. Spacers cannot be used with conditioned bushings.

TYPE DN-1B
DN/DN6-1B

TYPE DN-1B: Nozzle with extended tip, utilised in applications where it is desirable to have the gate feed on an "inside" surface of the part, or where fast cycles are needed (thin wall). Not suitable for fast change colour.
Only for polymers with low viscosity.
If compared with F series nozzles, DN nozzles have the sealing area on the external body rather than the tip and requires less accurate machining of the seat.

Catalogue

Multicavity nozzle
Single nozzle

YOU MUST FILL IN THE FIELD NOZZLE DIAMETER

Nozzle diameter:

Diameter of the nozzle seat

2D/3D drawings download - Nozzle

YOU MUST FILL IN THE FIELD HEATER

YOU MUST FILL IN THE FIELD LENGTH

Heater wire exit:

Heater wire exit can be on the top or in the middle of the nozzle. Heater wire exit in the middle allows the replacement of heater whilst the mould is assembled on the injection device.

Nozzle length:

Distance in the mould between the lower surface of the nozzle head and the injection gate. The gate is at the end of the nozzle and the beginning of the moulded piece.

2D/3D drawings download - Bushing

YOU MUST FILL IN THE FIELD TYPE BUSHING

Type Bushing:

Nozzle bushing can be normal or conditioned.

YOU MUST FILL IN THE FIELD BUSHING LENGTH

Bushing Length:

Conditioned bushing are without spacers and they are provided in 2 standard lenghts.

YOU MUST FILL IN THE FIELD SPACER HEIGHT

Spacer Height:

Spacers can be used when it is required to have a bushing longer than the standard ones. Spacers cannot be used with conditioned bushings.

TYPE TF/FN-1 TF/TF6-1 ~ FN/FNH6-1T ~ FN/FNH6-1MDT ~ FT/FTH6-1MD

TYPE TF-1B15 TF/TF6-1B15

TYPE TF-1B50 TF/TF6-1B50

TYPE TF-1GLT TF/TF6-1GLT

TYPE TF/FN-1D TF/TF6-1D ~ FN/FNH6-1D

TYPE TD/DN-1 TD/TD6-1 ~ DN/DN6-1

TYPE TD-1B35 TD/TD6-1B35

TYPE TD-1GLT TD/TD6-1GLT

TYPE DN-1B DN/DN6-1B

TYPE TF/FN-1
TF/TF6-1 ~ FN/FNH6-1T ~ FN/FNH6-1MDT ~ FT/FTH6-1MD

TYPE TF-1B15
TF/TF6-1B15

TYPE TF-1B50
TF/TF6-1B50

TYPE TF-1GLT
TF/TF6-1GLT

TYPE TF/FN-1D
TF/TF6-1D ~ FN/FNH6-1D

TYPE TD/DN-1
TD/TD6-1 ~ DN/DN6-1

TYPE TD-1B35
TD/TD6-1B35

TYPE TD-1GLT
TD/TD6-1GLT

TYPE DN-1B
DN/DN6-1B